Hi Eero,
Regarding no holding torque: All the should be required for there to be holding torque is power and enable. Are the 3 KStep LEDs on?
In case something strange has been Flashed to KFLOP it can be reset to its Virgin state by re-Flashing New Version.
Search found 2559 matches
- Mon May 13, 2024 12:28 am
- Forum: Configuration Issues
- Topic: G0 Rapid feeds not following KMotion settings
- Replies: 5
- Views: 33
- Mon May 13, 2024 12:23 am
- Forum: Hardware Interface Issues
- Topic: Encoder AB Z
- Replies: 1
- Views: 7
- Sat May 11, 2024 12:00 am
- Forum: Configuration Issues
- Topic: G0 Rapid feeds not following KMotion settings
- Replies: 5
- Views: 33
Re: G0 Rapid feeds not following KMotion settings
Hi Eero, I can't duplicate the problem with those settings. If I code G0 X100 M30 I see a feedrate of 10.3 inches/minute which seems correct. Also if I double the KFLOP Velocity to 28000 steps/sec the feedrate doubles to 20.6 inches/minute. What are you doing and seeing? One issue is the Cnts/inch o...
- Fri May 10, 2024 6:48 pm
- Forum: Configuration Issues
- Topic: G0 Rapid feeds not following KMotion settings
- Replies: 5
- Views: 33
Re: G0 Rapid feeds not following KMotion settings
Hi Eero, I can't think of why that would be. What Version are you running? Please post your Initialization file and your Trajectory planner settings. Also the GCode that shows the problem. Are you executing the C Program? You might upload the settings from KFLOP to verify the settings are actually b...
- Wed May 08, 2024 7:50 pm
- Forum: User PC Applications and Libraries .Net
- Topic: KMotion_dotNet.dll not found
- Replies: 4
- Views: 53
- Tue May 07, 2024 5:23 pm
- Forum: User PC Applications and Libraries .Net
- Topic: KMotion_dotNet.dll not found
- Replies: 4
- Views: 53
Re: KMotion_dotNet.dll not found
Hi Tray,
Maybe the required version of .NET is missing on the PC? Does the example SimpleFormsCS run?
You might read this Thread.
Maybe the required version of .NET is missing on the PC? Does the example SimpleFormsCS run?
You might read this Thread.
- Tue May 07, 2024 5:19 pm
- Forum: Noise, Grounding, Shielding Issues
- Topic: Isolating SnapAmp from KFLOP to remove motor noise
- Replies: 6
- Views: 96
Re: Isolating SnapAmp from KFLOP to remove motor noise
Hi Griffin, I was curious what you thought about the impact of placing 30KHz band-reject filter on the ground connection between the SnapAmp and KFLOP, such that switching transients don't conduct into the logic ground. Do you think this would pose any advantages? Although the switching occurs at 30...
- Mon May 06, 2024 5:18 pm
- Forum: New Feature Request
- Topic: Log Bit Status
- Replies: 1
- Views: 20
Re: Log Bit Status
Hi kilzilkaya, It would be nice if you explained what you are trying to accomplish. If you need these bits in another Windows App it would be better to have the app read them directly. You might look at or use the function: bool CScreen::ReadBitCached(int bit) You can get the Virtual bits individual...
- Sat May 04, 2024 5:44 pm
- Forum: Configuration Issues
- Topic: Problem with KMotion Configuration screen
- Replies: 2
- Views: 31
Re: Problem with KMotion Configuration screen
The C Program Parameters must be contiguous without embedded comment lines to be imported correctly.
Try importing example \KStep\InitKStep6AxisSpindleAxis6.c to see if it imports correctly.
Try importing example \KStep\InitKStep6AxisSpindleAxis6.c to see if it imports correctly.
- Fri May 03, 2024 7:41 pm
- Forum: KMotionCNC, G Code Files, Offsets, Post Process
- Topic: Macro programs in KMotionCNC
- Replies: 1
- Views: 45
Re: Macro programs in KMotionCNC
Hi Alexanders, No 'IF' and 'WHILE' aren't supported. But the similar functionality can be achieved with looping subroutine calls. See the example SubroutineWithConditionals.ngc shown below: G20 #100 = 5 (examples of logical operations) (result is 1 if condition is true) (result is 0 if condition is ...